B Y : S H E R W O O D I N D U S T R I E S L T DOWNER’S MANUALEG31-118 FOCUSSHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS M
Maintenance And ServiceFUEL CONVERSION:Figure 8: Removing valve cap.5. Convert the burner orice(s):a) Remove the main burner orice with a inch de
11Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 9), rotate it counter-c
12Initial InstallationCheck draftwith a matchor smoke ina " (6 mm)tube locatedhere.Warning: Failure to position the parts in accordance
PREPARING YOUR FOCUS FOR INSTALLATION:1. Remove the appliance and surround panels from the packaging; check to make sure there is no da
There are two (2) main pieces to each corner bracket (see Figure 17). When installing the corner pieces into the trim the “B FACE” sides must
15Initial InstallationQUALIFIED INSTALLERS ONLYThese screws will keep the trim tight against the surround. Route the wiring harness through the hole i
16Initial InstallationQUALIFIED INSTALLERS ONLYCONVERTING A DIRECT VENT FIREPLACE TO A B-VENTED FIREPLACE:existing and attach with three (3) sheet met
Install sealed throat connector orflashing to prevent leakage of roomair up through chimney.DV Only: Before installing ventliners, mark each liner on
18FANTP TP/THTHFanControl120oF (49oC)Temperature SensorBlueOrangeBlackWhite GreenWhiteBlackOrangeWhiteGreen/YellowPower Cord120V AC300oF (149oC) Manua
Initial InstallationQUALIFIED INSTALLERS ONLYGAS LINE CONNECTION:Warning: Only persons licensed to work with gas piping may make the necessary gas con
FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must be
Secondary InstallationLOG SET AND EMBER INSTALLATION:The placement of the logs is not arbitrary. If they are positioned incorrectly, the ames can be
21Secondary InstallationBRICK PANEL INSTALLATION:Caution: Use only the type of ember material supplied with this replace. Due to the irregular size o
Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas c
23Parts List - ComponentsReference Number Part Description Part 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-0012 300°F (149°C) Spill Switch EC-00
Reference Number Part Description Part Number10 Door Only - Painted EG31-09211 Venturi EG31-099Owner’s Manual EG31-118” NTP Male Comp. 90° Elbow EG
25Parts Diagram - Body
Parts List - Surrounds & FasciaReference Number Part Description Part NumberSteel Bay Face - Nickel 50-092Steel Bay Face With Glass - Painted 50-
27Parts Diagram - Surrounds & Fascia
Reference Number Part Description Part NumberCast surround only - Painted 30-036Cast surround only - Antique White 30-035AWCast surround only - Diamon
29Reference Number Part Description Part Number31 Cast front only (no surround, glass, valve door, or clip) - Antique White 50-40331 Cast front only (
Table of Contents3Safety Precautions...2Table of Con
Parts Diagram- Cast Bay Front 30
31WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to
Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs o
3320. Sherwood Industries Ltd. is free of liability for any damages caused by the replace or stove, as well as inconvenience expenses and materia
34Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________
DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially
WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poison
Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before OperatingLIGHTING INSTRUCTIONS:ThermopileThermocoupleF
Move the rod located behind thepiezo ignitor to increase or decreaseprimary air at the venturi tube.There is only one (1) venturi and one (1) air shut
8Maintenance And ServiceROUTINE MAINTENANCE:At least once a year, run through the following procedures to ensure the system is clean and working prope
9to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong plastic bag.
Comments to this Manuals