Enviro C-11288 Owner's Manual

B Y : S H E R W O O D I N D U S T R I E S L T DOWNER’S MANUALEG31-118 FOCUSSHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS M

Maintenance And ServiceFUEL CONVERSION:Figure 8: Removing valve cap.5. Convert the burner orice(s):a) Remove the main burner orice with a  inch de

11Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 9), rotate it counter-c

12Initial InstallationCheck draftwith a matchor smoke ina " (6 mm)tube locatedhere.Warning: Failure to position the parts in accordance

PREPARING YOUR FOCUS FOR INSTALLATION:1. Remove the appliance and surround panels from the packaging; check to make sure there is no da

a) Attach one side trim to the top trim using a corner bracket (see Figure 16) to secure pieces together. There are two (2) main pieces to each corner

Figure 19: Surround Panel installation.15Initial InstallationQUALIFIED INSTALLERS ONLYThe standard surround panel comes with a fan controller and burn

16Initial InstallationQUALIFIED INSTALLERS ONLYCONVERTING A DIRECT VENT FIREPLACE TO A B-VENTED FIREPLACE:existing and attach with three (3) sheet met

Install sealed throat connector orflashing to prevent leakage of roomair up through chimney.DV Only: Before installing ventliners, mark each liner on

18The Focus will operate without electrical power. This model has a Millivolt gas control which uses the pilot ame to generate enough electric

Initial InstallationQUALIFIED INSTALLERS ONLYGAS LINE CONNECTION:Warning: Only persons licensed to work with gas piping may make the necessary gas con

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must be

Secondary InstallationLOG SET AND EMBER INSTALLATION:The placement of the logs is not arbitrary. If they are positioned incorrectly, the ames can be

21Secondary InstallationBRICK PANEL INSTALLATION:Caution: Use only the type of ember material supplied with this replace. Due to the irregular size o

Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas c

23Parts List - ComponentsReference Number Part Description Part Number1 120°F (49°C) Ceramic Fan Temperature Sensor EC-0012 300°F (149°C) Spill Switch

Reference Number Part Description Part Number10 Door Only - Painted EG31-09211 Venturi EG31-099Owner’s Manual EG31-118” NTP Male  Comp. 90° Elbow EG

25Parts Diagram - Body   

Parts List - Surrounds & FasciaReference Number Part Description Part NumberSteel Bay Face - Nickel 50-092Steel Bay Face With Glass - Painted 50-

27Parts Diagram - Surrounds & Fascia    

Reference Number Part Description Part NumberCast surround only - Painted 30-036Cast surround only - Antique White 30-035AWCast surround only - Diamon

29Reference Number Part Description Part Number31 Cast front only (no surround, glass, valve door, or clip) - Antique White 50-40331 Cast front only (

Table of Contents3Safety Precautions...2Table of Con

Parts Diagram- Cast Bay Front     30

31WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to

Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs o

3320. Sherwood Industries Ltd. is free of liability for any damages caused by the replace or stove, as well as inconvenience expenses and material

34Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially

WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) pois

Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before OperatingLIGHTING INSTRUCTIONS:ThermopileThermocoupleF

Move the rod located behind thepiezo ignitor to increase or decreaseprimary air at the venturi tube.There is only one (1) venturi and one (1) air shut

8Maintenance And ServiceROUTINE MAINTENANCE:At least once a year, run through the following procedures to ensure the system is clean and working prope

9to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong plastic bag.