Enviro Westport C-10794 User Manual

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R I E S

Maintenance And ServiceTO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLYFUEL CONVERSION:Warning: This conversion kit shall be installed by a qualie

Step 8. Install the new pilot injector supplied with this conversion kit. Simply screw the new injector inside the pilot hood and reinstall the hood

121 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.2 In accordance with the current ANSI Z223.1 NFPA 54, National

13Initial InstallationQUALIFIED INSTALLERS ONLYVENT PARTS:This replace have been tested and certied for use with SIMPSON DURAVENT TYPE GS PIPE FOR G

VentRestrictorPositions543210’(0 m)0’(0 m)5’(1.52 m)5’(1.52 m)10’(3.05 m)10’(3.05 m)15’(4.57 m)15’(4.57 m)20’(6.10 m)25’(7.62 m)30’(9.14 m)18’(5.49 m)

15Initial InstallationQUALIFIED INSTALLERS ONLYPLANNING YOUR INSTALLATION:When planning your installation, it will be necessary to select the proper l

Initial InstallationQUALIFIED INSTALLERS ONLYHORIZONTAL INSTALLATION:STEP 1. Set the appliance in the desired location. Check to determine if wall stu

17and attach to the exterior wall with the four screws provided. Before attaching the vent termination to the exterior wall, run a bead

18NOTES: (1) The four (4) wood screws provided should be replaced with the appropriate fasteners for stucco, brick, concrete, or other types of sidi

STEP 3. To install the Round Support Box/Wall Thimble in a at ceiling, cut a 10” square hole in the ceiling, centered in the hole drille

2FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must b

down to the roof level, as shown in Figure 24. Tighten the clamp around the pipe section. Use a level to make sure the pipe is truly vertical. With ro

21(2) Any occupied areas above the rst oor, including closets and storage spaces, which the vertical vent passes through, must be enclosed. T

Figure 28: Cathedral Ceiling Support Box Leveling.Figure 29: Cathedral Ceiling Support Box Installation.STEP 6. Complete the cathedral ceiling install

233. Set the appliance in the desired location. Temporarily place a 24” (61 cm) section with the non-crimped end on the unit 4. Install th

Figure 32: Assembly of Venting Kit.20. Align all straight sections of pipe, slipping all joints together and installing with three (3) sheet metal scr

25Initial InstallationQUALIFIED INSTALLERS ONLYVENTING INTO A CLASS ‘A’ CHIMNEY:This model is also certied and tested to vent into CLASS ‘A’ wood sto

Firebox TopFlue CollarAdapterUndo four "screws thathold flue collarelbow to unit.Figure 34: Step 3 of Converting Top Vented into Rear Vented.Fig

27Initial InstallationQUALIFIED INSTALLERS ONLYINSTALLATION OF TOP VENTED; HORIZONTAL TERMINATION:SidingExterior wallDrywallVent pipeInsidefinished co

28Initial InstallationQUALIFIED INSTALLERS ONLYFREESTANDING DRAFTHOOD ADAPTOR:This Drafthood Adaptor is a complete assembly and is ready to t onto yo

29Initial InstallationGENERAL VENTING INFORMATION:Canadian InstallationsThe venting system must be installed in accordance with the current CSA B149 i

Table of Contents3Safety Precautions...2Table of Con

30Initial Installation4. After a minimum of 10 minutes operation, test the chimney draft with a smoke match at the top row of the pattern to conrm th

31Initial InstallationQUALIFIED INSTALLERS ONLYGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the nec

32Figure 45: Gas Control Valve and Optional Thermostat Wiring.Initial InstallationQUALIFIED INSTALLERS ONLYELECTRICAL REQUIREMENTS FOR GAS VALVE AND O

Fan assemblyValve coverControl panel(Fan control location)Screw holeFigure 47: Optional Blower (Fan) Installation.Secondary InstallationINSTALLATION O

341. Carefully remove logs from box. Check to ensure there is no damage. It is very important to install all logs in their proper position

Secondary InstallationCAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED.Important note: When the unit is turned on for the rst

36Figure 57: Top brick panel in place, screws shown. Figure 58: Back brick panel in place.Figure 59: Side brick panels in place.Figure 56: Brick panel

Trouble ShootingProblem Possible Cause SolutionSpark will not light the pilot after repeatedly pressing the spark ignitorDefective piezo ignitor. • Ch

Reference Number Part Description Part Number1 Top Vent Insert Piece - Painted EGWP-5031 Top Vent Insert Piece - Antique White EGWP-503AW1 Top Vent In

39Reference Number Part Description Part Number6 Cast Leg (Each) - Painted EGWP-5086 Cast Leg (Each) - Antique White 50-3756 Cast Leg (Each) - Diamond

4DIRECT VENT ONLY: This type is identied by the sux DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec

Parts Diagram - CastWESTPORT - CastingsJanuary 200540

41Parts List - ComponentsReference NumberPart Description Part Number9 120° Ceramic Fan Temperature Sensor EC-00110 S.I.T. Nova Valve NG (50% Turn Do

Parts List - ComponentsReference NumberPart Description Part Number17 Rating Plate (Label) 30-04918 Gas Valve Cover 30-050Flue Connection 30-05119 Inn

43Parts Diagram - ComponentsWESTPORT - ComponentsJanuary 2005

WarrantySherwood Industries Ltd. offers a Limited Lifetime Warranty on this gas product. This limited lifetime warranty covers the appliance for a per

45Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

5SpecificationsWARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxid

6Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before OperatingWARNING: IF YOU DO NOT FOLLOW THESE INSTRUCT

72. Start the pilot by pressing the gas control knob and turning it to PILOT. While holding the gas control knob in, press the piezo ignitor several

8Electronicignition moduleMaintenance And ServiceROUTINE MAINTENANCE:At least once a year, run through the following procedures to ensure the system i

Figure 7: Handles for Removing Door.Figure 8: Removing of Door.Maintenance And ServiceREPLACING THE GLASS:The glass in the replace is a high temperat