PELLET STOVEMiniPLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS CO
EXHAUST AND INTAKE LOCATIONS:101/16"(255mm)61/8"(156mm)21/16"(53mm)Figure 8: Mini Inlet and Outlet Location. EXHAUSTBase of unit to cen
11Figure 10: Corner Installation. CORNER THROUGH WALL INSTALLATION:3" (75mm)3"(75mm)Wall thimblemanufacturedby pellet ventmanufacturer.Insta
InstallationHORIZONTAL EXHAUST THROUGH WALL INSTALLATION:Vent installation: install vent at clearances specified by the vent manufacturer.A chimney co
13Wall framingWall thimbleTermination capVertical sectionof vent pipeHorizontal framefor thimble90° elbowConcrete WallClean out teeWall framingWall th
15InstallationHEARTH MOUNT INSTALLATION:Rain capStorm collarSeal plate (cover plate)Existing masonry flueVent pipe (single wallstainless flex pipe ors
InstallationEXTERIOR MOUNTED EXHAUST BLOWER (20-070):The Mini can be equipped with an externally mounted exhaust blower. This optional ki
17InstallationTYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - HORIZONTAL TERMINATION:Electrical Cable90° Elbow45°Elbow with Rodentscreen
Roof SheathingRain CapRoof FlashingRoof RaftersCeiling JoistsVent PipeExterior WallSheathingOutside VentTerminationInstallationTYPICAL THROUGH WALL WI
19InstallationTHERMOSTAT INSTALLATION:1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the des
2Introduction...3Ratin
If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly,
21InstallationOPTIONAL PANEL KIT:This kit must be installed before the unit is started. Figure 32: Screws at back of the cab side.Figure 30: Screws ab
Installation123Figure 33: Installing Hopper Lid.Installing Hopper Lid:1. Attach the hopper brackets to the back of the unit with a screw in eac
23TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly
TroubleshootingüPoor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.üExhaust Temperatu
25Troubleshooting7. The convection blower will not function normally.üClean all grill openings at the back and below unit .üPress the fan button; does
Wiring DiagramConnectThermostatHereRedRedRedRedBrownBrownBrownBrownWhiteWhiteWhiteWhite115VWhite220VBlueWhiteWhiteOrangeOrangeOrangeOrangeYellowYellow
27Parts ListReference Number Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 Auger Motor - 115V EF-0013 High Limit Temp
Parts ListReference Number Description Part Number 17 Burn Pot 50-116618 Burn Pot Liner 50-116719 Burn Pot Bottom 50-116820 Front Louvers 50-116921 L
29Parts Diagram - ComponentsMini - ComponentsNovember 2006
3Introduction* This manual is designed for the technician in conjunction with the owner’s manual. *RATING LABEL LOCATION:The rating label is located o
Parts Diagram - SteelMini - Steel ComponentsNovember 200630
31WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to
WarrantyExclusions and Limitations:1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint. 2. This Warranty exclude
33Warranty17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surf
34NAME OF OWNER:_________________________________________ADDRESS:_____________________________________________________________________________________
4IntroductionSOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the h
5IntroductionINSTALLATION: Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspe
InstallationDECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:1. Remove the right and left hand cabinet sides by loosening the three (3) T-20 To
7InstallationAPPLIANCE DIMENSIONS AND SPECIFICATIONS:Figure 2: Dimensions of Mini. 151/2"(393 mm)187/8"(481 mm)171/2"(444 mm)195/8"
InstallationCLEARANCES TO COMBUSTIBLES:IMPORTANT: Attach the Mini’s Hearth Pad when installing the unit on a combustible floor. The supplied hearth pa
9hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.3. Termination must exhaust above the inlet ele
Comments to this Manuals