PELLET STOVEEvolutionPLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIO
10hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.3. Termination must exhaust above the inlet e
InstallationOUTSIDE FRESH-AIR CONNECTION:This Heater must have adequate air for proper combustion in the room that it is installed.Figure 7: Outside A
Figure 10: Corner Installation. InstallationMOBILE HOME INSTALLATION:4" (10 cm)4"(10 cm)Fresh Air IntakeWall thimblemanufacturedby pellet ve
13 InstallationHORIZONTAL EXHAUST THROUGH WALL INSTALLATION:Vent installation:
InstallationTHROUGH WALL WITH VERTICAL RISE AND HORIZONTAL
152 ft(61 cm)Rain Cap (ensure capis at least 3ft (91cm)above the roof at thelowest point)Roof FlashingRoof RafterFire Stop withSupport CollarCeiling J
HEARTH MOUNT INSTALLATION:EF 5Existing FireplaceClean Out TeeFireplace DamperLocationRain CapSeal PlateVent Pipe (singlewall stainless flexpipe or PL
17InstallationEXTERIOR MOUNTED EXHAUST BLOWER:The Evolution can be equipped with an externally mounted exhaust blower. This optional kit includes all
InstallationTYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - HORIZONTAL TERMINATION:Electrical CableEF 590° Elbow45°Elbow with Rodentscree
19EF5Roof SheathingRain CapRoof FlashingRoof RaftersCeiling JoistsVent PipeExterior WallSheathingOutside VentTerminationInstallationTYPICAL THROUGH WA
2Safety Warnings & Recommendations...3Installation...
InstallationTHERMOSTAT INSTALLATION:1. Install the wall thermostat (12 or 24 Volt rated) in a location that is not to close too the unit but will effe
21InstallationSLIDER/DAMPER SET-UP:This is used to regulate the airflow through the pellet stove. The slider damper should be set by a trained technic
TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly.
23TroubleshootingüPoor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.üExhaust Tempera
Troubleshooting7. The convection blower will not function normally.üClean all grill openings at the back and below unit .üPress the fan button; does t
25Wiring DiagramConnectThermostatHereRedRedRedRedBrownBrownBrownBrownWhiteWhiteWhiteWhite115VWhite220VBlueWhiteWhiteOrangeOrangeOrangeOrangeYellowYell
Parts ListReference # Description Part #1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001Window Channel Tape - 1.8m (72”) EC-0582 Auger Motor - 220
27Parts ListReference # Description Part #Door Gasket - 7ft (213 m) 50-08823 Top Louver Set - Nickel 50-09724 Ash Shelf Louver 50-162Slider Damper Rod
Parts Diagram - ComponentsEVOLUTION - ComponentsMay 200728
29Parts Diagram - SteelEVOLUTION - Steel ComponentsMay 2007
3Safety Warnings & Recommendations* This manual is designed for the technician in conjunction with the owner’s manual. *Please read this entire Ow
30NAME OF OWNER:_________________________________________ADDRESS:_____________________________________________________________________________________
4Safety Warnings & RecommendationsCLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This will vary du
5Safety Warnings & RecommendationsFRESH AIR: Outside Fresh Air connection is optional. Fresh Air must be connected to all units installed in “Air
Remove the two (2)wood screws (oneon either side of theunit) to remove theunit from the pallet.InstallationRATING LABEL LOCATION:The rating label is l
InstallationDIMENSIONS:7IMPORTANT: When not installing the optional Hearth Pad on the unit, the minimum requirements for protection on c
InstallationCLEARANCES TO COMBUSTIBLES:This unit can be installed on a combustible floor when installed with the optional hearth pad part 50-1568 (for
9InstallationHEARTH PAD PEDESTAL INSTALLATION:This unit can be installed on a combustible floor (e.g. linoleum, hardwood flooring) when the Optional
Comments to this Manuals